Injectors and coils are where the ECU actually makes power happen, and they are also where two of the most expensive swap mistakes live. Both mistakes come from the same root: assuming a driver is a driver and a coil is a coil. They are not. An injector driver has to match the injector’s impedance, and an ignition output has to match whether the coil has a built-in igniter or not. Get either wrong and the result ranges from “runs badly” to “melts the ECU’s output stage.” This one is worth reading before you order injectors or coils, because the parts you choose decide what the wiring has to be.
Injectors: impedance decides the driver
Every fuel injector is an electromagnet. The ECU switches it to ground, current flows, the pintle lifts, fuel sprays. The question is how much current, and that is set by the injector’s coil resistance, its impedance. There are two camps.
High-impedance (high-Z) injectors measure roughly 10 to 16 ohms. Because the resistance is high, the current is naturally limited to around an amp or so. The ECU can simply switch full battery voltage across the injector and hold it there for as long as it wants it open. This is called a saturated drive: one steady on-signal, valve opens and stays open until the signal ends. It is simple, cheap, and reliable, and it is what the vast majority of modern port-injection engines use.
Low-impedance (low-Z) injectors measure roughly 1 to 5 ohms. If you tried to switch full voltage across a 2-ohm injector and hold it there, current would climb to five-plus amps and stay there, cooking the injector and the driver. So low-Z injectors need a smarter drive: peak-and-hold. The driver hits the injector with a high current spike to snap the pintle open fast (commonly in the region of 4 amps), then drops back to a much lower hold current (roughly 1 amp) that is enough to keep it open without overheating anything. Peak-and-hold opens the injector slightly quicker, which is one reason big high-flow injectors historically favoured low-Z, but it needs a driver stage built for it.
The first mistake: wiring low-Z injectors to a saturated driver. Some ECUs have peak-and-hold drivers, some have saturated only, and some (the Haltech Elite range and MaxxECU’s SPORT, RACE and PRO, for example) have current-controlled drivers that can run either type, set up in software. Others need help with low-Z injectors: FuelTech’s FT450 and FT550 need an external peak-and-hold driver, and Link’s G4X range is built for high-Z injectors, so low-Z ones need ballast resistors. If you bolt low-impedance injectors onto a saturated-only output, you overload the driver and risk destroying it. The reverse, high-Z injectors on a peak-and-hold driver, generally works but can under-drive if the hold current is set too low. The safe path: know your injector impedance before you buy, and confirm the ECU has the right driver type and channel count. Whether an output is peak-and-hold, saturated, or switchable is spelled out in the ECU spec sheet, and it is one of the first things to check.
A note on resistors. Ballast is the other route: a pack with one resistor in series with each injector, such as Link’s BAL6. Each injector still uses one normal injector output, and you re-check the dead times afterwards. It is still a workaround, not a design. It wastes the fast-open benefit of low-Z and adds heat and failure points. If you have the choice, match the driver to the injector properly. And in practice, most modern swaps are simply running high-Z injectors on saturated (or switchable) drivers, which sidesteps the whole issue, so unless you have a specific reason to run low-Z, high-Z keeps the wiring simple.
How many injector outputs you actually need
The output count follows the fuel strategy, and it is worth getting right because it drives the whole ECU choice. Sequential (fully individual) port or direct injection needs one driver per cylinder: a straight six wants six, a V8 wants eight. Grouped or batch injection pairs cylinders onto shared drivers, so it needs cylinders divided by two. Throttle-body injection might need only one or two central injectors. Direct injection is its own world: the high-pressure GDI injectors need a dedicated DI driver stage that most standalones do not have natively, so a DI build usually pulls an add-on driver module rather than ruling the ECU out.
If you want to run true sequential injection, and most people building a modern engine do, you need a driver per cylinder plus the software to fire them in the right order. Whether that is worth it over batch is a real tuning trade-off, and working out the driver count for your specific engine is exactly what matching ECU I/O to your engine walks through.
Ignition: smart vs dumb is the whole game
Ignition wiring has a fork in the road that catches more swappers than injectors do, because the words are confusing and the parts look similar. The question is whether your coils are “smart” or “dumb.”
A smart coil (also called a logic-level coil, or a coil with a built-in igniter) has the driver electronics (an IGBT) built into the coil pack itself. You feed it power, ground, and a low-voltage logic trigger signal straight from the ECU, and the coil handles the heavy switching internally. The ECU output just needs to send a clean 5V (or thereabouts) square wave. Most modern coil-on-plug systems are smart: the GM LS coils, for example, are logic-level triggered.
A dumb coil (also called an inductive coil, or a passive coil) is just the transformer, with no built-in driver. It needs something to switch its primary current on and off, and that current is several amps. That “something” is an igniter, either built into the ECU’s ignition output (an inductive-capable driver) or added as an external igniter module. You cannot feed a dumb coil a logic-level signal and expect it to fire; there is nothing in it to do the switching.
The second mistake, and the more common and destructive of the two: connecting a dumb, inductive coil directly to a logic-level ignition output. The ECU’s logic output is designed to drive the tiny input of a smart coil’s internal igniter, not to switch the several amps a bare coil primary demands. Wire a dumb coil to it directly and you either get no spark, a weak spark, or a fried ECU output stage. Several popular OEM setups are dumb-coil and explicitly require an external igniter: the Toyota 2JZ-GTE VVT-i, the Nissan RB26’s early coils (which need a multi-channel external igniter), and the Ford Coyote, where Haltech’s own Coyote documentation is blunt about not connecting those coils straight to the ECU and recommends its HPI8 igniter instead.
So the wiring rule is: match the ignition output type to the coil. Smart coil, logic-level output, wire it directly. Dumb coil, you need an inductive-capable output or an external igniter sized to your channel count (an 8-cylinder dumb-coil setup needs 8 igniter channels). Some ECUs drive inductively on-board and some are logic-level only. If yours is logic-level only and your engine runs dumb coils, budget for an igniter module sized to the channel count from the start: the ECU maker’s own unit if there is one (an HPI8 for an 8-cylinder Haltech), otherwise a neutral one. It is not optional, and it is not something to discover after the harness is built.
How many ignition outputs
Same logic as injectors, driven by the ignition style. Coil-on-plug (one coil per cylinder) needs one output per cylinder. Wasted-spark (one coil fires two cylinders that reach TDC together) needs cylinders divided by two, so a straight six on wasted spark needs three. A single distributor needs just one output. Rotaries are their own case, with leading and trailing plugs per rotor. As with injectors, the count and the driver type together decide whether an ECU fits, which is the kind of thing the StandaloneHQ selector resolves automatically instead of leaving you to cross-reference datasheets by hand.
The practical checklist
Before you commit to injectors and coils, answer four questions and the wiring falls out of them. What is the injector impedance, high-Z (saturated) or low-Z (peak-and-hold), and does the ECU have the right driver type for enough channels? Is your ignition coil-on-plug, wasted-spark or distributor, and how many outputs is that? Are the coils smart (logic-level, wire direct) or dumb (inductive, needs an igniter)? And if they are dumb, does the ECU drive inductively on-board or do you need an external igniter module sized to the cylinder count?
Answer those honestly at the parts-buying stage and you avoid the two worst outcomes: an ECU that cannot drive what you bought, and a driver stage you damaged by feeding it the wrong load. Both are far cheaper to avoid on paper than to fix in the car.
Choosing coils and injectors and not sure the ECU on your shortlist has the right driver types and counts? The StandaloneHQ guided selector derives the exact injector and ignition outputs your build needs, flags peak-and-hold vs saturated and smart vs dumb, and calls out when an igniter or DI-driver module is required.
Manufacturer sources checked for this guide: Haltech Elite 2500 product page; MaxxECU injector output wiring; FuelTech FT450/FT550 manual; Link G4X XtremeX ECU; Haltech Coyote engine page; Haltech 2JZ/1JZ engine page; Haltech RB engine page; Haltech: do I need an igniter?.
Always verify against the manufacturer’s manual and your tuner before wiring.